Short answer: If your neighbours have low pressure too, it is likely a Scottish Water supply issue, so check its website or call 0800 0778 778. If it is just your home, the usual causes are a partly closed stop tap, an old narrow or lead supply pipe, a blocked strainer or a hidden leak. Each has a different fix.
Low water pressure is frustrating, and in Glasgow it has some local causes. A century old tenement can have a narrow supply pipe climbing four floors. A villa in Bearsden can have a long underground pipe from the street that has started to leak. And now and then Scottish Water is working on a main nearby. The trick is to work out which one you have before paying for the wrong fix.
Pressure or flow?
People say pressure, but what they usually notice is flow: how much water comes out. Pressure is the force pushing it. You can have decent pressure and poor flow if a pipe is narrow or partly blocked. A plumber measures both. A simple home test is to time how long the cold kitchen tap takes to fill a measuring jug. If it is much slower than it used to be, something has changed.
Step one: is it just you?
| What you notice | Likely cause | Who to call |
|---|---|---|
| Neighbours and the street have low pressure too | Scottish Water main or works | Scottish Water |
| Every tap in your home is weak, neighbours fine | Stop tap, supply pipe or a leak | Plumber |
| One tap or the shower only | That fitting, its valve or strainer | Plumber |
| Hot weak, cold fine | Boiler, cylinder or tank system | Plumber or heating engineer |
| Sudden drop with a hissing sound | Leak or burst | Plumber, urgently |
Ask a neighbour first. Scottish Water also lists supply issues by postcode on its website. Its customer helpline is 0800 0778 778, open 24 hours.
Common causes inside the home
A stop tap that is not fully open. After any plumbing job, check it. Old stop taps in Glasgow flats are often under the sink, in a press or under a floorboard by the door, and their washers can wear and partly block the flow. Our guide to finding the stop tap in a tenement flat shows where to look.
An old or narrow supply pipe. Many older Glasgow buildings still have their original pipework. Scottish Water says homes built before 1970 have a higher chance of lead pipework. Old iron pipe corrodes inside and the bore gets smaller. In a tenement, a rising pipe that serves several flats belongs in common to the flats it serves under the Tenements (Scotland) Act 2004, so replacing it may be a shared job.
A blocked strainer or filter. Some combis, shower valves and pressure reducing valves have small strainers. Grit or debris after mains work can block them.
A hidden leak. A leak on your supply pipe, under a ground floor or in the garden, lets water escape before it reaches the taps. Signs include hissing at the stop tap with every tap off, or ground that stays wet in dry weather.
Why top floors suffer
Water pressure falls with height. A top floor tenement flat has the furthest to climb, and if four flats share a narrow riser and two of them run showers at once, the top flat feels it most. Some top floor flats are also fed from a cold tank in the roof space, where the pressure depends on how high the tank sits above the taps. If that is your situation, our guide to shower pumps for top floor flats explains when a pump helps.
Hidden leaks and how we find them
If your pressure has dropped and nothing obvious has changed, a leak is worth ruling out. We close every tap and check whether water is still moving. Then we isolate sections of pipe to narrow down where it is. On the supply pipe outside, we may use listening equipment or tracer methods. Scottish Water is responsible for the main and the communication pipe up to and including the boundary stop cock. The supply pipe from there into your home is yours, as its lead pipes page sets out. See our leak detection page for how a trace runs.
Soft water: one thing you can rule out
In hard water parts of England, limescale narrows pipes and blocks shower heads. Glasgow’s water is soft. Scottish Water’s 2024 hardness data shows the Milngavie zones at about 16 mg/l as calcium carbonate. Scale is rarely the cause of low flow here. Corrosion in old iron, grit and worn valves are far more likely.
What not to do
Do not fit a booster pump straight onto the mains without advice. Scottish Water’s byelaws restrict pumps drawing directly from the supply, and a pump can starve the flats above or below you. Do not open up the stop tap with grips if it is seized, because old stop taps can snap. Call us instead.
Fixes at a glance
| Cause | Typical fix |
|---|---|
| Stop tap partly closed or worn | Open fully or replace the stop tap |
| Old or lead supply pipe | Renew the pipe from the stop tap to the flat |
| Blocked strainer | Clean or replace it |
| Hidden leak | Trace and repair |
| Shared riser in a tenement | Owners agree a renewal of the common pipe |
| Street supply | Scottish Water |
If you are in a Southside or West End tenement, our West End page explains how these buildings are usually plumbed.
Quick questions
Who do I call about low water pressure in Glasgow?
If the whole street is affected, Scottish Water on 0800 0778 778. If it is only your home, a plumber, because the supply pipe from the boundary stop cock inwards is the owner's responsibility.
Can a leak cause low pressure?
Yes. A leak on your supply pipe or inside the home can lower pressure, especially if it is a large one under a floor or in a garden.
Why is only my hot water pressure low?
On a combi, it can point to a partly blocked heat exchanger or filter. On a tank fed system, hot pressure depends on the height of the cold tank above the tap.
Will a water pressure booster pump help?
Pumps on mains supplies are restricted under Scottish Water's byelaws, so this needs proper advice. Fixing the cause is usually better.
Last updated 23 October 2026. Written for homes in Glasgow. Rules can change, so check the linked sources for the latest position.