Hot water cylinders
Hot water cylinders and water heaters in Glasgow
If your hot water is cold, lukewarm or the cylinder is leaking, the fault is usually the immersion heater, the thermostat, a valve or the cylinder itself. Many Glasgow flats still have a copper cylinder in a press cupboard. Bigger homes often have unvented cylinders, which must be installed by someone trained for them under Scottish building standards.

You need this when
- No hot water, or it runs out much faster than before
- Water dripping from the base of the cylinder or a valve
- Water dripping from a pipe outside, near the cylinder
- The immersion heater switch is on but the water stays cold
- Rumbling or ticking from the cylinder
- You are swapping a combi and want stored hot water
Cylinders in Glasgow homes
Older tenement flats often have a vented copper cylinder in a press cupboard, fed from a small cold tank above it or in the roof space, and heated by an immersion heater, a back boiler or a gas boiler. Many were removed when combi boilers arrived, but plenty remain, especially in flats with electric heating.
In bigger homes in Bearsden, Milngavie and Newton Mearns, where two or three bathrooms run at once, a system boiler with an unvented cylinder is common. It stores hot water at mains pressure, which gives strong showers throughout the house.
It helps to know which you have before you call. A small tank above the cylinder or in the roof space means a vented system. No tank, a white or coloured metal cylinder with a pressure vessel beside it and a pipe to a tundish means unvented. A cylinder with an immersion switch and no boiler connection is electric only.
Soft water and cylinders
Scottish Water's 2024 hardness data puts the Milngavie supply zones, fed from Loch Katrine, at about 16 mg/l as calcium carbonate, classed as soft. That means limescale on immersion elements and in cylinders is far less of an issue in Glasgow than in hard water parts of England. When an immersion fails here, it is more often the element burning out or the thermostat failing than scale. Corrosion and age are the main enemies of an old copper cylinder.
Unvented cylinders and Scottish building standards
An unvented cylinder is a sealed vessel at mains pressure, so it relies on safety devices. Standard 4.9 of the Scottish domestic technical handbook says installation should be carried out by a person with appropriate training and practical experience, which could include courses run through SNIPEF or CITB. The installer should be identified on the label, and the tundish and discharge pipe must go to a safe, visible point.
The handbook also says the safety devices should be maintained. An annual check of the expansion vessel charge, relief valves and discharge is good practice. Ask any installer about their unvented qualification before they start.
Replacing a cylinder or water heater
In small flats without gas, an electric cylinder or a point of use water heater under a sink can be the simplest choice. We look at how much hot water you use, where it can go and what your electrics can carry. Larger electric units need their own circuit, fitted by a qualified electrician.
A cylinder that leaks from the body itself, rather than from a valve or joint, cannot be repaired properly and needs replacing. Other signs are rusty or discoloured hot water, an immersion that keeps failing, or a cylinder too small for the household. When we replace a cylinder we check the size against the number of bathrooms and people, the recovery time from the boiler or immersion, and the space in the cupboard. A modern factory insulated cylinder also loses far less heat than an old copper one with a loose jacket.
What affects the price
The price depends on the type of cylinder, its size, access to the cupboard, whether the pipework needs changing, and electrical work. We confirm after a look.
| What | Price |
|---|---|
| Immersion heater element or thermostat | price confirmed after a look at the job |
| Unvented cylinder safety service | quote on survey |
| Replacement vented or unvented cylinder | quote on survey |
| Point of use or electric water heater | quote on survey |
No prices are shown on this site. Every job is priced after a look at it, by photo or a visit.
The visit
What happens, step by step
- 01
Identify the system
Vented with a cold tank, unvented mains pressure, or electric only. Each has different parts and safety checks.
- 02
Test the heat sources
We test the immersion element and thermostat and, where the boiler heats the cylinder, the valves and controls.
- 03
Check the safety devices
On unvented cylinders we check the expansion vessel, pressure relief and temperature relief valves and the discharge pipe.
- 04
Repair or replace
Parts are replaced where it makes sense. A leaking cylinder body needs a new cylinder, sized for your household.
FAQ
Hot water cylinders: what people ask
Why is my immersion heater not heating?
The element may have burned out, the thermostat may have failed or tripped, or the timer or switch may be faulty. We test each with a meter.
Water is dripping from a pipe outside near my cylinder. Is that bad?
On an unvented cylinder that pipe is usually the safety discharge. Water from it means a valve or the expansion vessel needs attention. Call for a check soon.
Do I need a water softener in Glasgow?
No, not for limescale. Glasgow's water is soft, according to Scottish Water's published figures.
Should I keep my cylinder or switch to a combi?
If you have one bathroom and good mains pressure, a combi can work well. With several bathrooms or weak pressure, stored hot water is usually better.
Where