For one plumber in Glasgow

Own plumberinglasgow.co.uk and this website

  • The domain plumberinglasgow.co.uk
  • A search report: what people in Glasgow type for this trade each month
  • This website, with your own job photos in place of ours
  • Your Google Business Profile set up
  • 2 weeks of Google Ads management free (you only pay Google for the clicks)

Message Matthew at BetterWays, who own the domain.

See the search report for Glasgow

Glasgow and the towns around it

Get a free quote

Hot water cylinders

Immersion heater not working: what to check

Last updated 23 October 2026 · 4 minute read

Short answer: If your immersion heater is switched on but the water stays cold, check the switch, the fused spur and the timer first, then the circuit breaker in the consumer unit. If those are fine, the thermostat or the heating element has usually failed. Both can be replaced. In soft water Glasgow, scale is rarely the cause.

Row of new copper plumbing fittings

Where immersion heaters are still common in Glasgow

Plenty of combi boilers have gone into Glasgow kitchens, but immersion heaters are still everywhere. Older tenement flats and cottage flats in Paisley often have a copper cylinder in a press cupboard with an immersion heater screwed into the top or side. In some it is the only source of hot water, usually where the flat has electric storage heaters. In others it is a backup to a gas boiler.

You will also find immersions in unvented cylinders in bigger homes, and in some flats with electric only heating in Renfrew and the newer blocks near the river.

An immersion heater is simple. It is an electric element inside the cylinder, like a big kettle element, controlled by a thermostat. Power comes from a switch on the wall, usually a fused spur or a double pole switch, sometimes through a timer. When it fails, it is usually one of a short list of parts.

Work through the checks in order

Start with the easy things. Do not open the immersion cap yourself. It has live mains terminals inside.

CheckWhat to look for
Wall switchIs it on, and is the neon light lit if it has one
Timer or programmerIs it set to the right time and in an on period, and has a power cut reset the clock
Boost buttonSome controllers have a boost. Try it to see if the water heats
Fuse in the spurSome spurs have a cartridge fuse that can blow
Consumer unitHas the immersion circuit breaker or the RCD tripped
Dual immersion switchSome older cylinders have a bath and sink switch. Try both

If the timer lost its settings after a power cut, that is often the whole problem. If the breaker or RCD has tripped and trips again when you reset it, stop there and switch the immersion off. That points to a fault in the element or the wiring.

For a power cut affecting your street, call 105.

The thermostat

The thermostat sits in a tube beside the element and switches it on and off. It usually has a dial set somewhere around 60°C. Most immersion thermostats also have a safety cut out that trips if the water overheats. If the cut out has tripped, there is often a small reset button under the cover.

A thermostat can fail in two ways. It can fail open, so the element never gets power and the water stays cold. Or it can stick closed, so the water keeps heating until the cut out trips. If your hot water is far too hot, switch the immersion off and get it checked. Scalding water is a real risk, especially for children and older people.

The element

If power is getting to the immersion and the thermostat is working but nothing heats, the element has probably burned out. Elements do wear out with age. A failed element can also leak current and trip the RCD.

In many hard water parts of the UK, the classic cause is limescale baking onto the element until it overheats. Glasgow is different. Scottish Water’s 2024 hardness figures class the Milngavie zones, fed from Loch Katrine, as soft at about 16 mg/l as calcium carbonate, and the other zones around Glasgow in the same table are soft or moderately soft. You can check the exact zone for your street with Scottish Water’s postcode checker. Our Glasgow water hardness guide explains more. So when an element fails here, age and electrical wear are the usual reasons, not scale. That also means fitting an expensive scale resistant element is not normally needed.

Replacing an element means turning off the water and power, draining the cylinder down below the element, unscrewing it with a special spanner, fitting a new one with a new washer and refilling. On an old copper cylinder the boss the element screws into can be fragile, so care is needed.

When the cylinder is the problem

Sometimes the immersion is fine and the cylinder is the issue.

  • If water is weeping from round the immersion boss, the washer or the boss itself may be failing.
  • If there is a leak from the body of the cylinder, or green or blue staining on the copper, the cylinder is near the end of its life.
  • If hot water runs out quickly, the cylinder may be too small for the household, the jacket may be thin, or one element of a dual immersion may have failed.

An old copper cylinder with a loose red jacket loses a lot of heat. A modern factory insulated cylinder holds its heat far better, which helps if you heat water on electricity.

Landlords

For privately rented homes in Scotland, the Repairing Standard requires a sink, a bath or shower and a wash basin with hot and cold water, according to mygov.scot. A failed immersion in a let flat where it is the only hot water source needs fixing promptly. Electrical safety in a rented home also needs an inspection by a registered electrician at least once every 5 years.

Getting it fixed in Paisley and Renfrew

Immersion faults are among the common jobs in older Paisley flats, alongside drain smells and winter pipe bursts. Our Paisley page covers the housing common there. For immersion repairs, cylinder swaps and electric water heaters, see our hot water cylinders service. If the work involves new wiring or a new circuit, it should be done by a qualified electrician. Scotland has no Part P, but electrical work still has to meet the building standards and the wiring regulations.

Quick questions

How do I know if my immersion element has gone?

If power is reaching the immersion and the thermostat is set correctly but the water never heats, the element is the likely fault. A plumber or electrician can confirm it with a meter.

Can I replace an immersion element myself?

It means draining the cylinder and working on a mains electrical connection. Unless you are competent with both, get a professional to do it.

Why does my immersion trip the electrics?

A failed element can leak current to earth and trip the RCD. Switch it off at the isolator and get it tested before using it again.

My water is scalding hot from the immersion. Is that a fault?

Yes. The thermostat may have stuck. Switch the immersion off and get the thermostat checked, because very hot water is a scald risk.

The serviceHot water cylinders in Glasgow Local notesPlumber in Paisley

Last updated 23 October 2026. Written for homes in Glasgow. Rules can change, so check the linked sources for the latest position.