Short answer: In a Glasgow tenement flat the stopcock is usually under the kitchen sink, in a press cupboard, under the floor near the front door or where the pipe enters the flat from the close. Some closes also have a main valve for the whole building in the close or cellar. Find yours now and check it turns.
Why it matters more in a tenement
In a house, a burst pipe floods your own floors. In a tenement, it floods the flats below as well. Glasgow has about 70,000 pre 1919 tenement flats, according to Glasgow City Council, and the Southside has thousands of them in Shawlands, Strathbungo, Battlefield, Langside and Mount Florida. When water is escaping, the minutes it takes to find the stopcock decide how many ceilings come down.
So the time to find it is now, not at two in the morning with water coming through the light fitting.
The usual places to look
Tenement flats have been replumbed many times over the decades, so the stopcock can be in odd places. Work through this list.
| Where | What to look for |
|---|---|
| Under the kitchen sink | A brass tap on the pipe coming up through the floor, often at the back of the cupboard |
| Press cupboards | Hall or kitchen presses where pipes come into the flat, sometimes behind stored items |
| Under the floor by the front door | Lift the hall carpet or a short floorboard near the door. The supply often enters from the close here |
| Bathroom | Behind the bath panel or near the toilet, in flats where the supply comes up the back wall |
| Beside the hot water cylinder | In flats with an old cylinder in a press, the cold feed valve may be nearby |
| In the close or landing | A valve on the rising pipe outside your door, sometimes in a small box |
Scottish Water says the most common locations are under a sink, in a garage or close to the hot water system, wherever the mains enters the home. Its frozen and burst pipes advice also points out that flats and terraces may share a water supply, with the stop valve normally where the supply enters the building.
The main valve for the close
Many tenements have a valve that shuts off water to the whole building. It can be at the foot of the close, in a cellar, in the back court or in a chamber at the front. If your own stopcock fails, or the leak is on a shared rising pipe, this valve stops it. Turning it off cuts water to every flat, so tell neighbours as soon as you can. Scottish Water advises checking with neighbours that turning off the water has not affected their supply.
If you have a property factor, ask them where it is. If your close self factors, it is worth the owners finding it together.
The boundary stop cock
There is usually another stop cock outside, in the pavement or at the boundary, sometimes called the toby. According to Scottish Water, it is responsible for the water main and the communication pipe up to and including the stop cock at the boundary. Owners are responsible for the supply pipe from the boundary into the property.
You should not normally need to touch the boundary stop cock, and in a tenement it often serves the whole building. If it is the only way to stop a leak, or it is damaged, call Scottish Water on 0800 0778 778.
Testing yours
Once you have found it:
- Turn it clockwise until it stops. Do not use force.
- Open the cold kitchen tap. The flow should slow and stop.
- Turn the stopcock back on fully, then back a quarter turn so it does not stick.
- Check for drips round the spindle.
If it will not turn, turns but does not stop the water, or leaks when you move it, it needs replacing. Old stop taps in Glasgow flats often have worn washers or spindles seized from years of not being used.
What to do if it is seized or missing
Do not force a seized stopcock with a wrench. The spindle can snap, or the old pipe it sits on can crack, and then you have a leak you cannot stop. We can isolate the supply at the close valve or the boundary, then fit a new stop tap. If your flat has no stop tap of its own, we can fit one where you can reach it, ideally under the kitchen sink.
While we are there, it is worth fitting small isolation valves on the toilet, taps and washing machine. Then a small leak means turning off one fitting rather than the whole flat.
Lead and old pipe
When you find your stopcock, look at the pipe it sits on. If it is dull grey, soft and shows silver when scratched, it may be lead. Scottish Water says homes built before 1970 have a higher chance of lead pipework. Our lead pipes guide explains what to do.
When water is already escaping
Turn off the stopcock, switch off the boiler and immersion, open the cold taps to drain the pipes and keep water away from electrics. If water is coming from above, knock on the flat upstairs. For the full step by step, see our emergency plumber page. If you live on the Southside, our Southside page covers the tenements and villas we work in there.
Quick questions
My flat does not seem to have its own stopcock. Is that normal?
In some older tenements, yes. The flats may share a supply with one main valve for the building. A plumber can fit a stop tap for your flat.
Which way do I turn a stopcock?
Clockwise to close, like most taps. Scottish Water says it normally closes by turning clockwise.
My stopcock will not turn. Should I force it?
No. Forcing an old stop tap can snap the spindle or crack the pipe. Get it replaced before you need it in an emergency.
Who owns the stop cock in the pavement?
Scottish Water is responsible for the communication pipe up to and including the stop cock at the boundary of your property.
Last updated 23 October 2026. Written for homes in Glasgow. Rules can change, so check the linked sources for the latest position.