Short answer: If your condensing boiler stops in freezing weather, often gurgling with a fault code, the condensate pipe outside has probably frozen. Find the plastic pipe where it leaves the wall, pour warm water, not boiling, slowly along it until the ice clears, then reset the boiler as the manual shows. If it will not restart, call an engineer.
Why this happens in Glasgow
Almost every gas boiler fitted in recent years is a condensing boiler. It squeezes extra heat out of its flue gases, and that makes water, called condensate. The condensate runs through a plastic pipe, usually about the size of a sink waste, to a drain. Often that pipe runs outside along a wall to a gully.
Condensate trickles out slowly. In a hard frost, the water sitting in the outside section freezes. The pipe fills with ice, the condensate backs up into the boiler, and the boiler shuts itself down to protect itself.
Glasgow gets enough frost for this to happen every winter. The Met Office records about 46 days of air frost a year at its Glasgow Bishopton station, with around 10 each in December and January. East Kilbride sits higher than the city and on exposed ground, so it can feel colder still. Many of the town’s houses from the 1950s to the 1970s had their old back boilers swapped for combis, with condensate pipes run outside down harled walls. On a frosty morning in The Murray or Greenhills, that is the classic fault.
Signs it is the condensate pipe
- The boiler has stopped and the weather is below freezing, or has been overnight.
- You hear gurgling or bubbling from the boiler.
- The display shows a fault or lockout code. Manufacturers use different codes, so check your manual.
- The boiler starts, then cuts out again after a few minutes.
- Outside, the pipe has ice at the open end or feels solid.
How to thaw it, step by step
- Find the pipe. It is plastic, often white or grey, coming out of the wall near the boiler and running down to a drain or gully. Follow it from the boiler side if you are not sure.
- Find the frozen part. It is usually at the lowest point, a bend, or the open end where it meets the drain.
- Use warm water. Fill a watering can or jug with warm water from the tap or a kettle that has cooled. Not boiling.
- Pour slowly along the pipe, starting at the open end and working up. Repeat until you can hear or see water draining.
- Or use a hot water bottle or a warm cloth held on the frozen section if you cannot pour.
- Reset the boiler. Most have a reset button or a reset sequence in the manual. It may take a few minutes to start.
- Watch the ground. Warm water poured on a path will freeze. Put grit or salt down.
Only work on the outside pipe. Do not remove the boiler casing. Anything inside the boiler is gas work and needs a Gas Safe registered engineer.
What not to do
| Do not | Why |
|---|---|
| Use boiling water | It can crack the plastic and scald you |
| Use a blowtorch or heat gun | Fire risk and the pipe can melt |
| Climb ladders on ice | Call for help if the pipe is high up |
| Keep resetting with the pipe still frozen | The boiler will just lock out again |
| Take the boiler casing off | That is gas work for a Gas Safe engineer |
Stopping it happening every winter
If your condensate pipe freezes most winters, it can be improved. Common fixes include:
- Run it inside. Connecting the condensate to an internal waste, such as the kitchen sink trap or a soil stack, keeps it in the warm. This is often the best fix.
- Make the outside run shorter. The less pipe outside, the less there is to freeze.
- Use a wider pipe outside. Wider pipe takes much longer to freeze solid. Manufacturer guidance usually sets a minimum size for external runs.
- Insulate it. Waterproof pipe insulation on the outside section helps.
- Check the fall. The pipe should slope steadily downhill. A dip or a flat run lets water sit and freeze.
- Trace heating. A low power heating cable can be fitted where nothing else works.
These are changes to the condensate pipe, which is part of the boiler installation. Ask a Gas Safe registered engineer to do it, ideally at the next service, so it is ready before the first frost.
If the boiler still will not start
Some boilers need a second reset or a few minutes before they run. If it still locks out with the pipe clear, the cause may be something else: low pressure, a blocked condensate trap inside the boiler, a fault with the fan or ignition, or no gas. Check the pressure gauge, and check that other gas appliances work. Our guide to no hot water goes through the other checks.
If you smell gas at any point, stop, open windows, leave and call the National Gas Emergency Service on 0800 111 999.
Getting help in East Kilbride
We repair combi and system boilers across East Kilbride and the rest of South Lanarkshire. See our boiler repair page for what a visit involves, and our East Kilbride area page for the homes and faults most common there.
Quick questions
Can I use boiling water on a frozen condensate pipe?
No. Boiling water can crack plastic pipe and scald you. Use warm water, like you would for a bath or washing up.
Is it safe to keep resetting the boiler?
Clear the blockage first. If the boiler locks out again after the pipe is clear, stop and call a Gas Safe registered engineer.
My condensate pipe is inside. Can it still freeze?
Rarely. Most freezes happen on the outside section. If the whole pipe is indoors and the boiler still gurgles, it may be blocked rather than frozen.
Can the pipe be moved so it does not freeze?
Often yes. Running it to an internal waste, using a wider pipe outside or insulating the outside run all help.
Last updated 23 October 2026. Written for homes in Glasgow. Rules can change, so check the linked sources for the latest position.