For one plumber in Glasgow

Own plumberinglasgow.co.uk and this website

  • The domain plumberinglasgow.co.uk
  • A search report: what people in Glasgow type for this trade each month
  • This website, with your own job photos in place of ours
  • Your Google Business Profile set up
  • 2 weeks of Google Ads management free (you only pay Google for the clicks)

Message Matthew at BetterWays, who own the domain.

See the search report for Glasgow

Glasgow and the towns around it

Get a free quote

Boiler repair

No hot water: combi and cylinder checks

Last updated 23 October 2026 · 4 minute read

Short answer: With no hot water, first work out your system. On a combi, check the pressure gauge, the display for a fault code, the gas supply and, in a frost, the condensate pipe. On a cylinder system, check the programmer, the immersion and the cylinder thermostat. If heating works but hot water does not, a diverter valve is a common culprit.

Hand turning a thermostatic valve on a white radiator

First, which system do you have

The right checks depend on how your home makes hot water. In East Kilbride, most houses built from the 1950s to the 1970s have long since swapped their back boilers and old cylinders for a combi, usually in the airing cupboard or the kitchen. Older flats in Glasgow may still have a cylinder in a press cupboard. Bigger homes often have a system boiler and an unvented cylinder.

What you seeSystem
Boiler only, no hot water tank anywhereCombi
Boiler plus a cylinder, no tank in the loftSystem boiler with unvented cylinder
Boiler, cylinder and a cold tank in the loftRegular boiler with vented cylinder
Cylinder with an immersion switch, no boilerElectric only

Combi boiler checks

A combi heats water only when you open a hot tap. If nothing comes through warm, go through these.

Pressure. Look at the gauge on the front or underneath. Most manufacturers ask for about 1 to 1.5 bar when the system is cold. Below that, many combis will not fire. Your manual shows how to top up using the filling loop. If it keeps dropping, read our boiler losing pressure guide.

Fault code. Write down any code or flashing light. The manual explains what it means. Many codes are a lockout that you can reset once.

Condensate pipe. In a frost this is the most likely cause in East Kilbride. The town sits higher than central Glasgow, and many houses have the condensate pipe running outside down a harled wall to a gully. When it freezes, the boiler shuts down, often with a gurgling noise. Pour warm water, not boiling, slowly along the outside section, then reset. Our frozen condensate pipe guide has the details.

Gas. Does the gas hob light? If not, the problem may be the gas supply or your meter. If you have a prepayment meter, check the credit. If you smell gas at any point, open windows, leave and call the National Gas Emergency Service on 0800 111 999.

Cold water flow. A combi needs a decent flow of cold water before it fires for hot water. If the cold tap at the kitchen is weak too, the problem may be the stop tap partly closed, a supply fault or a frozen pipe. In that case it is a water supply problem, not a boiler fault.

Power. Check the boiler has power, the fused spur is on and the display is lit.

Heating works but hot water does not

This is very common on combis. Inside the boiler, a diverter valve sends hot water either round the radiators or to your taps. If it sticks in the heating position, the radiators get hot but the taps stay cold. The fix is a repair inside the boiler, which is gas work.

A blocked or failed flow sensor or plate heat exchanger can do the same. In hard water towns, scale in the plate heat exchanger is a classic cause. Glasgow and East Kilbride are on soft water according to Scottish Water’s 2024 hardness data, which puts the Daer zones that serve parts of Lanarkshire at about 32 to 35 mg/l as calcium carbonate, classed as soft. So here wear and sludge from the heating side are more likely than scale.

Cylinder system checks

If you have a cylinder, the boiler only heats the water when the programmer and the cylinder thermostat ask it to.

  • Programmer. Is the hot water channel set to on, or in a timed on period? Power cuts can reset the clock.
  • Cylinder thermostat. A small dial strapped to the cylinder. If it is turned right down, the boiler will not heat the water.
  • Motorised valve. On many systems a valve opens to let boiler water into the cylinder coil. If it sticks shut, the radiators heat but the cylinder does not.
  • Immersion. Try the immersion heater. If the water heats on the immersion, the boiler side is the problem. If neither heats it, see our immersion heater guide.
  • Thermal cut out. On unvented cylinders, a safety cut out can trip and stop heating. It is designed not to reset itself, so find out why it tripped.

When it is a job for an engineer

Anything inside the boiler casing is gas work. In Great Britain that must be done by a Gas Safe registered engineer. Ask to see their ID card and check it on the Gas Safe Register. The card shows what types of gas work they are qualified for.

It helps to have the boiler make and model, the fault code and what you have already tried ready when you call. It means the engineer is more likely to bring the right part first time.

Landlords and tenants

For privately rented homes, the Repairing Standard requires hot and cold water to the sink, bath or shower and wash basin, according to mygov.scot. Gas appliances must also be checked every year by a Gas Safe registered engineer. If you are a tenant with no hot water, tell your landlord or agent in writing.

East Kilbride and the rest of Lanarkshire

No hot water calls in East Kilbride peak in cold snaps, because of frozen condensate pipes, and after the heating is first switched on in autumn, when parts that have sat idle all summer stick. Our East Kilbride page covers the housing and typical faults there. For a diagnosis and repair, see our boiler repair service.

Quick questions

Why do I have heating but no hot water on my combi?

The most common cause is a faulty diverter valve, which switches the boiler between heating and hot water. A low flow of cold water into the boiler can also stop it firing for hot water.

Why do I have hot water but no heating?

Check the thermostat and programmer first. If they are calling for heat, the pump, a zone valve or the diverter valve may be stuck.

Should I keep resetting the boiler?

Once or twice is fine after clearing an obvious cause like a frozen condensate pipe. If it keeps locking out, call a Gas Safe registered engineer.

Could the problem be my gas meter?

If other gas appliances like the hob are not working either, check your prepayment credit or whether the meter valve is open. If you smell gas, call 0800 111 999.

The serviceBoiler repair in Glasgow Local notesPlumber in East Kilbride

Last updated 23 October 2026. Written for homes in Glasgow. Rules can change, so check the linked sources for the latest position.