Short answer: A leaking toilet usually leaks from one of four places: the supply pipe or valve, the seal between the cistern and the pan, the pan connector at the back, or the pan itself if cracked. Dry everything with tissue, flush, and watch where water first appears. Condensation on a cold cistern can look like a leak too.
In Hamilton’s council era houses built after the war, the bathroom is usually upstairs, above the hall or kitchen. A leaking toilet in those homes does not always leave a puddle you can see. Often the first sign is a brown ring on the ceiling below or a floorboard that feels soft next to the pan. Finding exactly where the water comes from is the key, because the fix for each spot is different.
Four places a toilet leaks
| Where | When it leaks | Typical fix |
|---|---|---|
| Supply pipe, isolation valve or fill valve connection | All the time, flushed or not | Tighten or replace the fitting or valve |
| Seal between cistern and pan, or cistern bolts | During and just after a flush | Replace the doughnut seal and bolt washers |
| Pan connector at the back of the pan | During a flush | Replace the pan connector |
| Cracked pan or cistern | Depends where the crack is | Replace the pan or cistern |
How to trace it
You need dry kitchen roll and a torch.
- Dry the floor, the pipes, the back of the pan and the underside of the cistern completely.
- Wait ten minutes without flushing. Wipe each joint with tissue. A wet patch now points to the supply, the valve or the cistern itself.
- Flush once. Watch the bolts under the cistern and the joint where the cistern meets the pan. Then check the pan connector at the back, where the pan joins the soil pipe.
- Wipe the pan from top to bottom, looking for a fine crack.
Put a few drops of food colouring in the cistern before you flush. Coloured water on the tissue tells you it came from the cistern, not the supply.
Condensation: the leak that is not a leak
In a Glasgow winter, cold mains water fills the cistern and the bathroom air is warm and damp after a bath. Water condenses on the outside of the cistern and drips onto the floor. It looks exactly like a leak.
Signs it is condensation: the whole cistern surface is beaded with water, it is worse in cold weather and after showers, and there is no single source when you trace it. Better ventilation, an extractor fan or a cistern with an insulated liner helps. A fill valve that keeps refilling because of a worn flush valve makes it worse, because cold water keeps coming in. Our guide to a toilet that keeps running explains that fault.
The pan connector
The pan connector is the flexible or rigid fitting between the back of the toilet and the soil pipe. It often fails when a toilet has been moved slightly, the floor flexes, or the connector is old and has hardened. Because it is behind and below the pan, it is the leak most likely to go unnoticed until the ceiling below is stained.
In a house with timber floors, a pan that is not screwed firmly to the floor rocks slightly with use, and that movement works the connector loose. When we replace a connector, we check the pan is secure.
Old pipework in older Hamilton homes
Hamilton’s Victorian sandstone villas and terraces near the town centre can have older supply pipes. Scottish Water says homes built before 1970 have a higher chance of lead pipework, as its lead pipes page explains. A leak at the toilet supply is a good moment to look at what the rest of the pipe is made of.
Why act quickly
A small leak at the base of the toilet soaks the floorboards or chipboard. In time the floor softens and the pan becomes unstable, which makes the leak worse. If the toilet is upstairs, the ceiling below can stain or sag.
For landlords in Hamilton and across South Lanarkshire, the Repairing Standard requires a working toilet, drainage and a safe water supply, and has specific timescales for damp and mould. mygov.scot says landlords must inspect damp or mould within 10 working days of being told.
What we do
We trace the leak, fix the part that has failed, check the pan is secure and the floor is sound, and test it. If there is no isolation valve on the toilet supply, we fit one. If the pan or cistern is cracked, we quote for a replacement, and a like for like replacement does not usually need a building warrant in Scotland, as our building warrant guide explains.
Our toilet and tap repairs page covers the service, and our Hamilton page explains the homes we work in there.
Quick checklist
- Turn off the isolation valve if water is pooling
- Dry everything and trace with tissue and food colouring
- Rule out condensation on cold days
- Check the ceiling below for stains
- Call a plumber if it is the pan connector, a seal or a crack
Quick questions
Water appears round the toilet only after flushing. What is it?
Most likely the pan connector at the back, or the seal between the cistern and the pan. Both leak as water rushes through on a flush.
Water is there even when nobody has used the toilet. Why?
That points to the supply pipe, the valve, the cistern itself or condensation. Check whether the cistern is sweating on cold days.
Can a leaking toilet damage the ceiling below?
Yes. A slow leak soaks the floor and can stain or weaken the ceiling below long before you see much water on the bathroom floor.
Is a cracked pan repairable?
Not reliably. A cracked pan or cistern should be replaced.
Last updated 23 October 2026. Written for homes in Glasgow. Rules can change, so check the linked sources for the latest position.