Short answer: A tap that drips from the spout after it is turned off has a worn rubber washer or a worn ceramic cartridge. If the handle turns several times to close, it is a washer. If it closes in a quarter or half turn, it is a cartridge. In Glasgow's soft water, wear rather than limescale is almost always the cause.
A dripping tap is one of the most common small plumbing jobs in Kirkintilloch and Lenzie, where many homes are now on their second or third set of taps since the estates went up in the 1960s to the 1980s. The drip is annoying, it wastes water, and on a hot tap it wastes the energy too. The fix depends on what kind of tap you have.
Washer tap or cartridge tap?
Turn the tap on and off and notice how the handle moves.
| How the handle turns | Type of tap | What wears out |
|---|---|---|
| Several full turns from off to fully on | Traditional washer tap, often with crosshead or capstan handles | Rubber washer on the jumper |
| A quarter or half turn | Ceramic disc tap | Ceramic cartridge or its seals |
| Single lever moving up, down and side to side | Single lever mixer | Mixer cartridge |
Older bathrooms and kitchens in Kirkintilloch’s stone villas and early council houses may still have washer taps. Most taps fitted since the 1990s use ceramic cartridges.
Washer taps
A washer tap closes by pressing a rubber washer down onto a seat inside the tap body. Each time it closes, the washer squashes a little. Over years it hardens, splits or wears unevenly and stops sealing. Then it drips.
The fix is a new washer, and sometimes a new jumper, which is the small plate the washer sits on. If the seat inside the tap is pitted, it can be reground or a seat insert fitted. Washer taps are robust and simple to repair.
Ceramic cartridge taps
A ceramic disc tap has two discs with holes. Turning the handle lines up the holes to let water through. When the discs or the rubber seals on the cartridge wear, water gets past and the tap drips.
The fix is a new cartridge. The difficulty is that cartridges differ between brands and models. A cartridge has a spline count, which is the number of teeth on the spindle, plus a length and a thread. We take the old one out and match it, or identify the brand and order the right part.
Soft water: what it does and does not do
In hard water areas, limescale builds up on cartridges and washers and can cause drips. Glasgow’s water is soft. Scottish Water’s 2024 hardness data classes the Milngavie and Balmore supply zones as soft, at about 16 to 21 mg/l as calcium carbonate. Check your exact zone with Scottish Water’s postcode checker.
That means descaling your tap is unlikely to cure a drip here. The washer or cartridge is worn. Grit can also get into a cartridge after work on a main, which scores the ceramic discs.
Leaks at the base or under the sink
Water round the base of a mixer tap, especially one with a swivel spout, usually comes from a worn O ring. That is a cheap part, but it means taking the spout off.
Water in the cupboard under the sink is a different problem. Check the flexible tap connectors, which are the braided hoses from the isolation valves to the tap. They can corrode or split with age, and a failing one can burst. If yours look rusty or kinked, replace them. If there are no isolation valves under the sink, we fit them, so the tap can be worked on without turning off the whole house.
Doing it yourself
If you want to try:
- Turn off the isolation valve under the sink, or the stop tap.
- Open the tap to drain it.
- Put the plug in so small parts cannot fall down the waste.
- Remove the handle and cover to reach the headgear or cartridge.
- Take the old part to a plumbers’ merchant to match it.
Stop if the headgear will not move, because forcing it can crack an old tap body. Also stop if the isolation valve will not shut fully, because working on a tap under pressure floods the sink quickly. Old isolation valves in Kirkintilloch homes are often stiff from years of not being used, so turn them gently. Our guide on finding your stop tap helps if you have no isolation valves.
Repair or replace
| Situation | Repair or replace? |
|---|---|
| Washer tap in good condition | Repair |
| Cartridge available for your model | Repair |
| Cartridge no longer made | Replace |
| Body corroded or cracked | Replace |
| You want a different style | Replace |
If you replace a tap, choose one that suits your water pressure. Some taps are designed for high mains pressure and run weakly on a tank fed supply. The box usually says what pressure it needs.
What we do
We identify the tap, fit the right washer or cartridge, check the connectors and isolation valves, and test it. Our toilet and tap repairs page covers the service, and our Kirkintilloch and Lenzie page explains the homes we work in across G66.
Quick questions
Why does my tap drip after I turn it off?
The washer or cartridge inside is worn and no longer seals. Turning it tighter only wears it faster.
Is a dripping hot tap worse?
Yes, because you are also wasting the energy used to heat that water.
Water is coming from the base of the tap, not the spout. Is that the same?
No. That is usually a worn O ring on the spout or body. It is a different part but often a similar size job.
Should I repair or replace an old tap?
Repair if the tap is in good condition and parts are available. Replace if the body is corroded, parts are no longer made or you want a different style.
Last updated 23 October 2026. Written for homes in Glasgow. Rules can change, so check the linked sources for the latest position.